The company is interested in buying raw materials of such items:

  • Wastepaper grades MC-4A, MC-5B, MC-6B

    • MS-4A — Used non-moisture paper bags (no bituminous impregnation layer and reinforced layers)
    • MS-5B — Waste production and consumption of corrugated cardboard, paper and cardboard used in its production
    • MS-6B — All kinds of waste paperboard production and consumption (except electrical, roofing and footwear) with black and white color printing.

    Technical Requirements

    • Waste paper should not contain fiber, bags from under ashes, pasted with thermoplastic glue spine books moisture-waste paper and cardboard, unfit for consumption as fibrous material, covered with polyethylene and other polymer films, varnishes, resins, fabrics, foil, paraffined, bitumen, oiled, glue, metallized impregnated with chemicals, with wax, sand, rotten and burned.
    • Moisture of all groups paper should be no more than 15%
    • The mass of party is determing on 12% recycled moisture of waste paper.

    Pack

    • Waste paper must be packed in bales. One brand of waste paper should be paked in bales, weight from 200 to 600 kg but not exceeding 800 kg. Waste paper in the bails must be tightly compressed.
    • Piles should be tied soft steel wire diameter (2,5 ± 0,6) mm GOST 3282 or mild steel packaging GOST 3560 of Ukraine not more than 0,5 mm x 20.0 mm

    In your commercial proposals should contain the following data:

    • Quality features
    • Pack
    • Pricing and Availability

  • Technical timber (thickness of 8 to 45 cm in length from 2 to 4 m)

    Depending on the purpose timber must correspond to the conditions below

    • For the production of wood, wood fiber boards, and hydrolytic production:pa
      • The thickness of the upper end, at least 4 cm
      • Length, 1.0-6.0 m
      • Gradation in length, 1.0 m
    • For the production of wood-chip packaging, items of everyday and for industrial purposes:
      • The thickness of the upper end, not less than 6 cm
      • Length, 0.4 - 6.5 m
      • Gradation in length, 0.1 m

    Maximum deviations from the nominal length - from 0 to 0,1 m, and for the raw length is 1m ± 0,02m

    Raw requirements

    • The quality of wood raw material must correspond to the conditions below:
      • Rot and hollow. Allowed up to 1.2 diameter end with the release of the second end to 1.3 diameter
      • Outer rot. Not allowed
      • Burnt wood. Not allowed in the raw material for the production of fibreboard and particle board
    • Other defects of wood according to GOST 2152-93 are allowed.
    • The height of residual limbs of timber should not exceed 5 cm
    • Wood raw material can be delivered in the cortex or bark. Non-stripping bark.
    • Wood raw material thicker than 60 cm at the request of the consumer must be supplied in split form. In this case the maximum line splitting at the butts of any part thereof should not exceed 40 cm
    • Value of raw materials supplied by size and species groups (coniferous and deciduous) set in the contract between the consumer and the supplier.

    Accounting for wood raw material up to 3,0 m - GOST 3243-88, a length of 3.0 meters or more - GOST-2292-88.

    Requirements for packaging and labeling

    • Wood raw materials should be placed in transport packages.
    • For each package a label states the name of the manufacturer, and volume of the package.
    • Raw materials in the packages can be concluded in different directions. The package shall provide for storage of raw materials during transportation and handling operations.
    • In agreement with the consumer supplying of raw materials may be in non-packaging form.

  • Euro-Pallets (1200*1000, 1000*800,800*1200) GOST 9557-87 of Ukraine

    Technical Requirements

    • Pallets must be made in accordance with the standard for working drawings approved in due course. Pallet design should comply with GOST 9078 and be designed to withstand without residual strain workloads.
    • Wooden pallets details should be made of softwood lumber (pine, spruce, pine, larch) and lumber hardwood (alder, birch, poplar, oak, ash, beech, elm, acacia, maple, plane tree, chestnut).
      Notes
      1. In conifers and poplar annual rings width, measured at 10 rings should not exceed 7 mm.
      2. Production of poplar cross boards are not allowed.
    • Wooden pallets details must be without blemish: a sharp wane, sprout, rot, mechanical damage and foreign matter.
    • Dumb wane not allowed to use oak in other breeds - the cross boards, medium board and the establishment of the extreme outer edge of the boards of the flooring and foundation. In other cases, stupid wane allowed on each edge of two parts under the condition that they not bark Pors'k and size in the transverse direction does not exceed 15 mm. Suki diameter of 10 mm do not. Allowed increased knots.
    • In saber only allowed formation of shrinkage cracks. Each board allowed a deep crack length over the width of the board, if not crack formed in the preparation tray.
    • So-called "Pockets" are not allowed on the external layers of flooring boards and bases, and other surfaces allowed a length of 50 mm.
    • Slope of wood fibers is allowed no more than 5% on boards and 20% of charges.
    • Moisture when receiving trays - under GOST 9078.
    • Insects damage wood, except for poplar wood are not allowed. In poplar wood is allowed: in each shashtsi a wormhole diameter of 10 mm 2 in each board wormhole diameter of 10 mm, depth up to 5 mm.
    • Inner sapwood allowed in Hardwood, if not more than 1 / 4 the width of the board and 1 / 2 board thickness.
    • Core is allowed no more than three of the nine drafts tray.
    • Openings from a drop-down processing boards nesrosshihsya and tobacco rotten knots, exceeding the allowable size, should be laid with wood plugs of the same breed and board, using waterproof glue.
    • Boards must be integral.
    • Drafts should be made of a piece of wood or a piece of wood pulp press for 11,368 guests.
    • All surface pallet boards and drafts should be obpylyanoyi except fasok trailing edges of the boards of the foundation at the site of villas.
    • Surface roughness parameter tray - under GOST 9078.
    • Pallet boards make connections longitudinal cross-decking boards, further associations with ' flooring of the upper longitudinal and transverse frames, and frames the grounds of checkers. Longitudinal board flooring planks connecting the cross-screw nails chotyryhodovoho (Annex A) diameter of 3.5 mm, 60 mm in length navintovannoy of at least 75%. Allowed to board joints using nails to 2.5 M 60 under GOST 4028.
    • Allowed to perform the following markings embossed color. Lettering must be at least a depth of 0.3 mm, the paint should be from brown to black, non-water-soluble and does not lose color in light.

  • Sodium silicate, module 2.8 / 3.0 GOST 13079-81 of Ukraine

Contact page